AVTOBANK capture X.3 PARAMETERS VALUE PARAMETER PARAMETER TITLE HEX - DEC VALUE INTERPRETATION --------- ------------------------- ------- ---------------------------- 1 Command Mode Recall Char 0 0 No Recall Allowed 2 Echo 0 0 No Echo 3 Data Forwarding Signal 0 0 No Signal 4 Idle Timer 50 80--Multiples of .05 Second 5 Ancillary Device Control 0 0 No Use of XON/XOFF 6 Control of PAD Service Signals 0 0 No PAD Service Signals 7 Procedure on Break 0 0 Do Nothing 8 Discard Output (to Terminal) 0 0 Normal Data Delivery 9 Carriage Return Padding 0 0 No Padding 10 Line Folding 0 0 No Line Folding 11 Binary Speed C 12 2400 Baud 12 Flow Control of Pad by Term 0 0 No Use of XON/XOFF 13 Linefeed Insertion 0 0 No Linefeed Insertion 14 Linefeed Padding 0 0 No Padding 15 Editing 0 0 Disable Editing Function 16 Character Delete 8 8 CTRL-H 17 Line Delete 18 24 CTRL-X 18 Line Display 12 18 CTRL-R 19 Editing Pad Service Signals 2 2 Editing for Dsp Terminals 20 Echo Mask FF 255 No Echo of CR No Echo of LF No Echo of VT, HT, FF No Echo of BEL, BS No Echo of ESC, ENQ No Echo of ACK, NAK, STX, SOH, EOT, ETB, ETX No Echo of Editing Chars from X.3 Parms 16, 17, 18 No Echo of DEL and all Other Characters in Columns 0 & 1 21 Parity Treatment 0 0 No Checking or Generation 22 Page Wait 0 0 Disabled - 2 - NATIONAL PARAMETERS for 25017720156001 VALUE PARAMETER PARAMETER TITLE HEX - DEC VALUE INTERPRETATION --------- ------------------------ --------- --------------------------- 1 Linefeed Insertion 0 0 No Linefeed Insertion 4 Echo Mask INV 7 Pseudo Break 0 0 No Pseudo Break Character 11 Tab Padding 0 0--Pad Characters after HT 20 Half/Full Duplex 0 0 Full-duplex Terminal 21 Real Character Code 0 0 ASCII 23 Terminal Type 7F 127 **** 24 Permanent Terminal 0 0 Request Terminal ID 25 Manual/Automatic Connection 0 0 Manual (CONNECT required) 32 Automatic Hangup 0 0 In Command Mode upon Discon 34 Transmit on Timers 1 1 Enabled 36 Interval Timer 0 0 Disabled 37 Network Usage Display 0 0 Exclude Net-generated Usage Info in the Disconnected Msg 38 Carriage Return Padding-VAR 0 0--Pad Chars/10 Chars on a Line 39 Padding Option 0 0 Net Inserts no Pad Chars 42 DCE-TO-DTE XON Character 11 17 CTRL-Q 43 DCE-TO-DTE XOFF Character 13 19 CTRL-S 47 Pad Recall Value 1 Definition 1 1 Pad Recall Using @ 48 Operation After Pad Recall 1 1 Remain in Pad Command State 55 DTE-TO-DCE XON Character 11 17 CTRL-Q 56 DTE-TO-DCE XOFF Character 13 19 CTRL-S 57 Connection Mode 0 0 Transparent 60 Delayed Echo 0 0 Disabled 63 Parity Checking 0 0 Enabled 64 Early Acknowledgement 0 0--Packets Ack before Last Char 65 M-bit Handling 3 3 M-bit = 1 on Full Packets 66 Deferred Processn of User Input 0 0 Normal Processing 67 ESP Packetizing Option 0 0 Disabled 68 Escape Sequence Timer 0 0 Disabled 69 Escape Sequence Max Length 0 0 Disabled 70 Escape Sequence Initiator 0 0 Disabled 71 Parameter Reset on Disconnect 0 0 Reset To Init Value On Disc 72 EIA Flow Control FC 252 TX EIA Flow cntrl on CTS/RTS RX EIA Flow cntrl on CTS/RTS EIA Flow cntrl in use EIA permanently enabled RX normal signals TX normal signals О конфигурировании для приема файлов по протоколу Z-modem: ---------------------------------------------------------- Для передачи 8-битовой информации через порты Х.28 необходимо выставлять следующие значения параметров Х.3: для ТР8, ТР49 - 21:0,0:0,57:0(или 1),63:0 для ТР4 - 0:0,57:0(или 1),63:0 для ТР3 - 0:0,63:0 При передаче файлов через порты Х.28 они должны иметь определенные значения параметров Х.3: для ТР8, ТР49 - 2:0,3:0,4:1,9:0,10:0,13:0,14:0,15:0,21:0,22:0,0:0,57:0(или 1),63:0 для ТР4 - 2:0,3:0,4:1,9:0,10:0,13:0,14:0,15:0,0:0,57:0(или 1),63:0 для ТР3 - 2:0,3:0,4:1,9:0,10:0,13:0,14:0,15:0,0:0,63:0