PANASONIC EB 3510/HP600 NOTES: This is a dual NAM hand held unit. The ESN prefix is 136 decimal & 88 hex. Panasonic: 201-392-6053 NAM PROGRAMING: 1. This unit requires a programing adaptor, part number EB-WWG1036A, if you do not have one try the following: Locate the expansion connector on the bottom of the phone, remove the plastic cover if installed. Look at the connector with the small round antenna connector to the right (keypad facing up). There are four pins on each side (top and bottom) of the connector, the left bottom pin and right bottom pin must be shorted together. Use a bent paper clip to do this, the phone will wake up as soon as the clip makes contact. The clip must be kept in place during programing. Looking at the bottom of the phone: ______________________ | | | I I I I | <----- Top row. | 0 | <----- Antenna connector. | I I I I | <----- Bottom row. |______________________| ^ ^ | | | | Short these two pins 2. Phone will automatically power up. 3. Enter * 0 0 0 0 #, phone will display "MAINT MODE", you are now in maintenance mode. 4. Enter * 1 SND for NAM 1, or * 2 SND for NAM 2. Phone will display "NAM 1 MODE" or "NAM 2 MODE". Note that NAM 2 has entries 01 through 06 only. 5. Each data entry can be looked at by pressing RCL followed by the location (step) number below. 6. To store new data enter the value, press STO followed by the location (step) number below. For example to enter a system ID of 00031 enter 00031 STO 01. Data can be entered or reviewed in any order. 7. At any time press STO * * to complete programing and return to maintenance mode. 8. At any time press STO # # to ABORT programing and return to maintenance mode. 9. Press * 4 SND to exit maintenance mode. PROGRAMING DATA: STEP# #OF DIGITS/RANGE DISPLAY DESCRIPTION 01 00000 - 32767 SIDH SYSTEM ID 02 10 DIGITS OWNDL MIN (AREA CODE & TEL NUMBER) 03 0 OR 1 PRESYS PREFERRED SYSTEM 04 333 OR 334 IPCH INITIAL PAGING CHANNEL 05 2 DIGITS ACCOLC ACCESS OVERLOAD CLASS 06 2 DIGITS GIM GROUP ID (10 IN USA) 07 2 DIGITS DLMT DIALED DIGIT LIMIT (00= NO LIMIT) 08 08 ONLY SCM STATION CLASS MARK 09 UP TO 12 DIGITS SPDL SPEED DIAL NUMBER (PERMANENT NUMBER STORED IN LOCATION 00) 10 2 TO 4 DIGITS LOCK LOCK CODE 11 8 DIGIT, 0 OR 1 FCN 1 SEE NOTE 1 BELOW. 12 8 DIGIT, 0 OR 1 FCN 2 SEE NOTE 2 BELOW 13 8 DIGIT, 0 OR 1 FCN 3 SEE NOTE 3 BELOW NOTES: 1. Suggested entry is: 11000000. Bit 7/Digit 1 = Local use Mark Bit 6/Digit 2 = MIN Mark bit 5/Digit 3 = Not Used Bit 4/Digit 4 = Not Used Bit 3/Digit 5 = Silent Alert Bit 2/Digit 6 = Not Used Bit 1/Digit 7 = Not Used Bit 0/Digit 8 = Not Used 2. Suggested entry is: 00010100. Bit 7/Digit 1 = Not Used Bit 6/Digit 2 = Built in Monitor Bit 5/Digit 3 = Auto Lock (if set to 1 and unlock code is unknown phone will NOT enter program mode.) Bit 4/Digit 4 = Full Lock Bit 3/Digit 5 = Not Used (Enable only one of the following) Bit 2/Digit 6 = Allow user A/B select Bit 1/Digit 7 = Preferred system only Bit 0/Digit 8 = Home system only (no Roam) 3. Suggested entry is: 11000111. Digit 1 = Received call indicator Digit 2 = Continuous DTMF Digit 3 = Send Lock Digit 4 = Dial Lock Digit 5 = Not Used Digit 6 = Enable permanent timer (FCN 1) Digit 7 = Enable resetable timer (FCN 2) Digit 8 = Enable individual call timer READING ESN FROM HANDSET: 1. Power up phone as above. 2. Enter * 0 0 0 0 #. 3. Press * 3 SND. 4. Press 1 1 SND, phone will display decimal ESN, note that the leading "1" of the 136 ESN prefix will be omitted as the phone only has a ten digit display capacity. LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock UNLOCK: Enter two to four digit code. A/B SYSTEM SELECT: 1. Phone will default to preferred/non-preferred on every power up. 2. A only: F 7 2 3. B only: F 7 3 4. Home only: F 7 4