Nokia 2160 Test Mode
Name Change
Nokia 2160 Field Test Screens {31jan97}
The field test display can be activated in the NAM programming procedure.
(*3001#12345 MENU to enter programming mode).
These display are not meant for use by the end user.
There is a total of five field test screens. The display number is shownin
the top right corner of the screen. Use the up/down arrow keys to switch
between different displays. You can toggle the actual readings and the alpha
explanations of what they mean by pressing the "ABC" key.
Screen 1 - CS Display
(Digital control channel mode) (Digital traffic channel mode)
+----------+ +----------+
|rssi DVC S| |rssi s d|
|chan Pw A| |chan l a|
|CS-state | |CS-state |
+----------+ +----------+
(Analog control channel mode) (Analog voice channel mode)
+----------+ +----------+
|rssi D d| |rssi DVC S|
|chan Pw A| |chan l a|
|CS-state | |CS-state |
+----------+ +----------+
rssi = received Signal strength (dBm) [min= -113dBm, max= -51dBm, 2dB
steps]
DVC = Digital Verification Color Code [1-255, - = not locked]
D = DCC (Digital Color Code) on Analog Control CHannel [0-3,
- = not locked]
s = SAT color [0-2, - = not locked]
d = data receiving status
0 = no sync/no data
1 = sync/ not able to read
2 = reading correcting
3 = reading no correction
S = slot [1-3]
chan = Channel [0001-1023]
Pw = Max access power
DCCH: MS-ACC-PWR [0-10, - = not locked]
ACCH: CMAC [0-7, - = not locked]
l = Tx level [0-10, - = TxOff]
A = ?
a = audio state [0=off, 1=on]
CS-state = Cellular State
DCCH: SCAN-LOCK : Scanning and locking of DCCH
DCCH: DCCH-SEL : DCCH selection
DCCH: CAMPING : Camping
DCCH: REGISTR : Registration proceeding
DCCH: WAIT-ORDER: Waiting for order
DCCH: ORIGINAT : Origination proceeding
DCCH: RSELECT : Reselection
DCCH: ORIG-SMS : Origination SMS proceeding
DCCH: TERM-SMS : Terminated SMS proceeding
DTCH: TCH : Confirm traffic channel
xTCH: CONVERSAT : Conversation
ACCH: OOR : Out of range
ACCH: SCAN-PDCH : Scan primary dedicated control channels
ACCH: SCAN-SDCH : Scan secondary dedicated control channels
ACCH: SCAN-PCH : Scan paging channels
ACCH: IDLE : Idle
ACCH: ACCESS : Access
ACCH: VCH : Confirm voice channel
Screen 2 - CS Display
(Digital control channel mode) (Digital traffic channel mode)
+----------+ +----------+
|mode M C| |mode DTX|
|FB E SP pc| |ENCR CIPH|
|net SID| |d Be TA|
+----------+ +----------+
(Analog control channel mode) (Analog voice channel mode)
+----------+ +----------+
|mode | |mode |
|XSTBY | | |
| SID| | SAT |
+----------+ +----------+
mode = DCCH, DTCH, ACCH, AVCH
SID = system ID [0-32767, - = not locked]
DCCH:
M = maximum paging frame class supported by network [1-8]
C = current PFC (paging frame class) [1-8]
FB = number of F-BCCH slots
E = number of E-BCCH slots
SP = number of SPACH slots
pc = PCH subchannel
net = supported network types, bit map [1=suported, 0=not, C=current]
X = Public
X = Private
X = Residential
DTCH:
DTX = ?
ENCR = shown when message encryption is on
CIPH = shown when voice ciphering is on
d = data receiving status [0=no sync, 1=sync]
Be = Bit error rate in % [0-16]
TA = current time alignment [0-30]
ACCH:
XSTBY= shown when extended standby is on
AVCH:
SAT = SAT validity as measured by DSP [0-32767]
Screen 3 - CS Display (DCCH mode only)
+----------+
|RS SS SI b|
|NA ND |
| |
+----------+
RS = minimum Seceived signal Strength required to access cell [0-31]
SS = minimum signal Strength Sufficient for candidate of reselection
SI = Scan Interval between consecutive strength measurements in
hyperframes [1-16]
b = access burst sze [0=normal, 1=abbreviated RACH]
NA = Number of Analog neighbors [0-24]
ND = Number of Digital neighbors [0-24]
Screen 3 - Charging Display
+----------+
|bVo mod bs|
|Tbat1 Tb2|
|Wpwm FCmAh|
+----------+
bVo = battery voltage
mod = charging mode
FAS = FASt charge
COL = COLd charge
MAI = MAIntenance
ERR = wrong charger or battery not OK
LIC = LIthium Charge
TXO = TX-On charge
*** = charger disconnected
bs = battery is full or reason for fast charge termination
TI = max. charge TIme elapsed
DV = dV/peak value detected (full)
BV = Battery Voltage max limit
BT = Battery Temp max limit (overheat)
** = battery is not full
Tbat1 = battery temp. a/d reading [subtracted from 1023]
Tb2 = battery temp. in C (not implemented)
Wpwm = PWM charge control output [000-250]
FCmAh = mAh rating of charge given to the battery
Screen 5 - SW version display
+----------+
|ROM SW |
|EPROM SW |
|Prod type |
+----------+
ROM SW = ROM software version, e.g. V 65.08
EPROM SW = EPROM (flash) version, e.g. V 1.45
Prod type = product type, e.g. NHC-4NE
Screen 6 - "Normal" display
This screen is present only after a certain version of the EPROM software
(around 1.45). It is the non-test mode display...a welcomed addition
(thanks Nokia!)
--end