AM/FM Pocket Radio w/Built-In Alarm Clock
(120-0792A)                Operation                  Faxback Doc. # 56077

1.  To turn on the radio, slide POWER OFF/ON to ON.  The last selected
    band and station appear on the display.

2.  To change the bands between AM and FM, press BAND.  AM or FM appears
    each time you press BAND, and the last selected station if that band
    appears on the display.

3.  To change the station, press TUNE /\ or \/.  The radio beeps and the
    station changes on the display.

    To rapidly scan the stations, hold down TUNE /\ or \/ for about 1
    second.  When you release it, the tuner automatically stops at the
    next strong station.

    Notes:  For the best FM reception, fully uncoil the earphones' or
            headphones' cord, or fully extend the FM antenna.

            The AM antenna is built-in.  Move the radio to improve AM
            reception.

4.  Set MONO/FM-ST to MONO for monaural sound or FM-ST for stereo sound.

    Notes:  The sound from the radio's built-in speaker is always
            monaural.  To hear the radio's sound in stereo, use earphones
            or headphones.

            If MONO/FM-ST is set to FM/ST and earphones or headphones are
            connected, STEREO appears when the radio receives an FM
            broadcast in stereo.

            To improve reception of weak FM stations, set MONO/FM-ST to
            MONO.  The sound is monaural, but the reception should
            improve.

5.  Adjust VOLUME -/+ to a comfortable sound level.

6.  Slide E-BASS ON/OFF to ON to emphasize the bass sound.  Slide it to
    OFF for a normal bass sound.

7.  Set POWER OFF/ON to OFF to turn off the radio.

Setting the Time

1.  Set POWER OFF/ON to OFF.

2.  Press MODE twice.  The time and AM or PM flash.

3.  Repeatedly press HR to change the hour and MIN to change the
    minute(s).

    To rapidly change the digit(s), simply hold down HR or MIN.

4.  Press MODE to save the time setting.

    Note:  The time, AM or PM, and ALM (if an alarm time has previously
           been set) appears.

Setting the Alarm Time

1.  Set POWER OFF/ON to OFF.

2.  Press MODE once.  ALM appears, and AM or PM and the last set alarm
    time flashes.

3.  Repeatedly press HR to change the hour, and MIN to change the minutes.

    To rapidly change the digit(s), simply hold down HR or MIN.

4.  Press MODE twice to save the alarm setting you want and return to the
    time display.

Turning the Alarm ON/OFF

You can turn the alarm on or off from either the time display or the 
tuning display.

To turn the alarm on, press ALARM ON/OFF so ALM appears.

To turn off the alarm, press ALARM ON/OFF so ALM disappears.

At the preset alarm time, the alarm sounds.  To silence the alarm, press 
ALARM STOP.  The alarm sounds again at the same time the next day, unless 
you turn it off.

Memory Tuning

You can store up to 10 AM and 10 FM stations (20 stations in all) in your 
radio's memory so you can easily recall them.

Storing a Station

1.  Tune to the station you want to store.

2.  Press MEMORY.  M flashes.

3.  Within 10 seconds:

      For memory locations 1-5, press the corresponding memory location
      button (1-5).

      For memory locations 6-10, first press +5, then press 1 for location
      6, 2 for location 7, 3 for location 8, 4 for location 9, or 5 for
      location 10.

    M (for 0-5) or M+5 (for 6-10) appears for about 5 seconds.

Notes:  If M disappears before you press a memory location button, start
        again from Step 2.

        You cannot remove a station from memory, but you can store a new
        one in its place.

Recalling a Station

To recall a station stored in memory:

For memory locations 1-5, press the corresponding memory location button 
(1-5).

For memory locations 6-10, first press +5, then press 1 for location 6, 2 
for location 7, 3 for location 8, 4 for location 9, or 5 for location 10.

Note:  All memory stations are cleared when battery power is lost for more
       than about 20 seconds.

Key Lock

You can lock the tuning and memory controls on your radio to prevent 
accidental band, station, or memory changes.

To turn on key lock, hold down LOCK, then press MODE until LOCK appears.

To turn off lock, hold down LOCK, then press MODE again so LOCK 
disappears.

Note:  When you turn on lock, you can still turn the radio on and off and
       adjust VOLUME, FM-ST/MONO, E-BASS ON/OFF, and EAR/SPK.

Changing the AM/FM Band Step Rate

Your radio's AM/FM band is preset to tune in 10 kHz increments for AM and 
100 kHz for FM - the standard frequency steps for radio frequencies in the 
United States.  If you travel to other countries where the step rate is 9 
kHz for AM and 50 kHz for FM (Europe, for example), you can set your radio 
to tune in those increments by following these steps.

1.  Open the battery compartment and remove the batteries.

2.  Use a pointed object (such as a straightened paper clip) to set the
    switch inside the compartment to 10 kHz or 9 kHz (for the AM step
    rate).

3.  Replace the batteries and the compartment's cover.

    Note:  When you switch the step rate to 9 kHz, the clock changes from
           a 12-hour to a 24-hour format.

(EB 7/27/99)