Re: [TSCM-L] {1880} Re: Sealing a Room

From: kondrak <kon..._at_phreaker.net>
Date: Thu, 23 Aug 2007 18:08:18 -0400

Reginald Curtis wrote:
> To Kondrak,
>
> You may be correct. However, the ones I am speaking of are the flexible
> wire ones designed to wire up the resetable needle on demand type
> meters. I guess I should have specified that this type of meter is
> usually used only on houses or buildings which have a three phase
> entrance. I guess anything is possible, but I suspect that any attempt
> to open and reseal the device would have to leave some evidence of
> tampering.
>
> Again, you may be correct. I just have never had a problem with them.
> But then, how would I know if the bad guy was good enough?
>
> *Reg Curtis*
>
> From: /kondrak <kon..._at_phreaker.net>/
> Reply-To: /TSCM-L2006_at_googlegroups.com/
> To: /TSCM-L2006_at_googlegroups.com/
> Subject: /[TSCM-L] {1879} Re: Sealing a Room/
> Date: /Thu, 23 Aug 2007 16:49:16 -0400/
> >
> >Lead seals are worthless, most can be opened and re-closed with a
> sewing
> >needle and a pair of pliers with some rubber pads. The exact ones used
> >for electric meters are particularly poor.
> >
> >Reginald Curtis wrote:
> > > You can also use an actual seal. The easiest is the small wire
> ones with
> > > the lead lock at one end. Assuming it's a wooden structure, get
> four
> > > small eye bolts with screw ends. Screw two into the door and
> two into
> > > the frame. Pass the wire through the two on the door and then
> the two on
> > > the frame. Put the wire through the lead seal and crush it
> tight with
> > > your pliers. Using two eye bolts on each side prevents someone
> from just
> > > unscrewing them. You can purchase the seals
> > > in bulk or 'borrow' some from your local power utility which
> probably
> > > use them to seal residential power meters. Theirs probably have the
> > > company's logo cast into the seal. They are also individually
> numbered.
> > > About the only way in is to cut through the wire, and since you
> use one
> > > that is numbered, they cannot replace it without getting a
> similar one,
> > > which aside from governments, is virtually impossible. This is
> > > especially so if yours also has a logo cast into the seal that
> is not
> > > very common.
> > >
> > > *Reg Curtis*
> > >
> > > From: /"James M. Atkinson" <jm..._at_tscm.com>/
> > > Reply-To: /TSCM-L2006_at_googlegroups.com/
> > > To: /TSCM-L2006_at_googlegroups.com/
> > > Subject: /[TSCM-L] {1877} Re: Sealing a Room/
> > > Date: /Thu, 23 Aug 2007 10:43:22 -0400/
> > > >
> > > >Evidence tape works best.
> > > >
> > > >Once applied, is anybody moves the tape it will damage it, and
> tear.
> > > >
> > > >The downside is that getting the reside off the door can be
> trickey,
> > > >but you can buy a special adhesive remover in most automotive
> supply
> > > >stores that will make short work of the task.
> > > >
> > > >I would caution you to check the adhesive remover against the tape
> > > >itself as many evidence tapes can be removed merely by using
> adhesive
> > > >remover (which is a bad thing). So make sure that the you get
> > > >discoloration or destruction of the tape is a solvent is applied.
> > > >
> > > >-jma
> > > >
> > > >
> > > >
> > > >
> > > >At 04:50 AM 8/23/2007, kondrak wrote:
> > > >
> > > > >Depends on how much damage you're willing to tolerate...it
> can be as
> > > > >simple as a burglar alarm, to lasers and claymores.
> > > > >
> > > > >Perry Myers wrote:
> > > > > > Does anyone have any recommendations on sealing a room after
> > > a sweep? I
> > > > > > don't want to rely on easily obtainable tape rolls that could
> > > be easily
> > > > > > purchased. Other than a custom tape are there other methods
> > > you recommend?
> > > > > >
> > > > >
> > > > >
> > > > >
> > >
> >----------------------------------------------------------------------------------------------------
> > > > World Class, Professional, Ethical, and Competent Bug Sweeps, and
> > > >Wiretap Detection using Sophisticated Laboratory Grade Test
> Equipment.
> > >
> >----------------------------------------------------------------------------------------------------
> > > > James M. Atkinson Phone: (978) 546-3803
> > > > Granite Island Group Fax: (978) 546-9467
> > > > 127 Eastern Avenue #291 Web: http://www.tscm.com/
> > > > Gloucester, MA 01931-8008 E-mail: mailto:jm..._at_tscm.com
> > >
> >----------------------------------------------------------------------------------------------------
> > > > We perform bug sweeps like it's a full contact sport, we take no
> > > prisoners,
> > > >and we give no quarter. Our goal is to simply, and completely stop
> > > the spy.
> > >
> >----------------------------------------------------------------------------------------------------
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> >
> >
> >
> >
Received on Sat Mar 02 2024 - 00:57:15 CST